How Should You Compare Two Wholesale Bag Quotes Line by Line?
Two quotations for the same tote arrive at the same time, one at 12.40 and one at 14.80 per unit. The instinct is to take the lower number. In most wholesale programmes that instinct costs more than it saves, because the two figures almost never describe the same bag.
A quote is not a price. It is a list of inclusions, exclusions and assumptions, and the number at the bottom is only as good as the specification behind it. Comparing quotes line by line is the discipline that turns two documents into one decision.
What the unit price actually contains
Material grade, construction detail, hardware specification, operations performed, tooling, packing, inspection, freight basis, payment structure and minimum order. Move any one of those and the number changes by more than the gap between most competing quotes.
The failure this prevents
Buyers who compare only the headline price usually discover the difference three months later, in the form of a thinner lining, a lighter buckle, an omitted pull test or a carton that collapses in transit. By then the price comparison is settled and the cost is already committed.
What this method asks of you
A specification defined well enough to compare against, both quotes in writing, and roughly ninety minutes with a spreadsheet. The result is a landed cost per unit and a shortlist that reflects what you will actually receive.
- Normalising the Quotes First
- Line 1: Material and Grade
- Line 2: Construction and Reinforcement
- Line 3: Hardware and Plating
- Line 4: Operations Included
- Line 5: Tooling and Setup
- Line 6: Packing and Cartons
- Line 7: Inspection and Testing
- Line 8: Freight, Terms and Duties
- Line 9: Payment Terms and Cost
- Line 10: MOQ and Price Breaks
- Line 11: Lead Time Risk
- Line 12: Exclusions and Assumptions
- Building the Landed Cost
- Scoring the Non-Price Factors
- The Follow-Up Questions
- Documenting the Decision
- Using the Comparison in Negotiation
- Comparing Repeat Order Quotes
- Comparison Mistakes to Avoid
- Comparing Samples Against the Quotes
- When Both Quotes Are Above Budget
- A Reusable Comparison Template
- FAQ

Normalising the Quotes First
Same currency, same incoterm, same quantity
Before reading a single line, put both quotes on the same basis: one currency at one exchange rate, one incoterm, one order quantity, one payment structure. A comparison across different bases measures the bases rather than the suppliers.
Rebuild the quantity assumption
Ask both suppliers to price the same quantity, even if your plan sits between two of their tiers. Where a supplier only quotes at their own minimum, convert both to a landed cost per unit at your target volume.
The specification column
Add a third column to your spreadsheet containing your own specification. Without it you are comparing two documents to each other rather than to what you asked for, which is how an omission becomes invisible.
Date every quote
Write the date received and the validity period at the top of each column. A quote that expired last month is not a comparison, it is a reference point, and prices in coated fabric move with the resin market rather than with your planning cycle.
Line 1: Material and Grade
The substrate behind the coating
Ask what the PU is coated onto: woven fabric, non-woven, or a knit backing. Weight in grams per square metre and backing type drive both hand feel and durability, and they are the two numbers most often left out of a quote.
Coating thickness and finish
Coating thickness, surface finish and whether it is a standard or a named grade. A quote that says only PU leather has said nothing comparable, because the range within that term spans a factor of two in cost.
Lining specification
Lining material, weight and colour. Polyester taffeta at 190T and a brushed twill are different products, and swapping one for the other is the most common quiet substitution in wholesale bag production.
Who supplies the material
Whether the factory buys on the open market or from a nominated supplier affects consistency more than price. Ask both suppliers to name the mill and whether they can hold that mill across repeat orders.
Line 2: Construction and Reinforcement
Seam allowance and stitch density
Ask for stitch density in stitches per inch and seam allowance in millimetres. A quote at eight stitches per inch with a ten millimetre allowance describes a different product from one at six stitches with eight millimetres, and the labour content differs accordingly.
Reinforcement at load points
Handle anchors, strap junctions and D-ring tabs should be listed with their reinforcement: interlining weight, rivets, bar tacks, number of passes. Where a quote is silent, the reinforcement is whatever the line decides on the day.
Internal structure
Base board, gusset stiffener, pocket construction and lining attachment. A bag that stands unaided and one that folds flat can carry the same outer appearance and a materially different cost.
Edge treatment method
Painted, folded, bound or raw, and how many coats where painted. Edge treatment is a visible quality signal, a meaningful cost line, and the specification most often left as a word rather than a number.
Line 3: Hardware and Plating
Material and finish
Zinc alloy, brass or steel, with the plating named: antique brass, light gold, matte nickel. Plating colour and durability vary widely at similar price points, and mixed plating is a visible defect at retail.
Weight as a proxy
Ask for the weight per piece of the main hardware. Lighter hardware at the same appearance usually means less material or a thinner plating, and the difference shows up in a season rather than at delivery.
Zipper specification
Tape width, teeth type, slider brand and whether the zip is cut to length or made to measure. A named slider on a generic chain is common; ask which part carries the name.
Setting method
Press-set with a dedicated die or hand-set. Press setting is faster and more consistent; hand setting introduces variation around snaps and rivets that appears as deformation and loosening.
Nickel release and destination rules
Where metal hardware touches skin, several markets restrict nickel release. A quote that specifies plating without naming the compliance test has not considered the destination, and testing after production is expensive.
Line 4: Operations Included
List every operation, then tick
Cutting, skiving, edge folding, gluing, stitching, hardware setting, edge painting, cleaning, threading, folding, bagging, carton packing. Ask each supplier to tick the operations included and state which are charged separately.
What “labour included” hides
A quote that includes assembly but excludes edge painting, or includes packing but excludes the poly bag, is not comparable. The gaps are rarely large individually and commonly total five to eight percent of the unit price.
Sampling and setup labour
Sample making is usually charged separately and sometimes credited against the order. Confirm the charge, the number of revisions included and whether the credit exists, because the difference affects the true first-order cost.
Rework responsibility
State who performs and pays for rework on defects found at final inspection. Unstated, the answer defaults to the buyer’s account through a price adjustment that is difficult to challenge later.
Line 5: Tooling and Setup
One-time charges listed separately
Cutting dies, embossing plates, printing screens, pattern development and any brand-specific jig. These should appear as separate lines rather than folded into the unit price, so that repeat orders can be compared on the same basis.
Amortisation and ownership
Whether a tooling charge is amortised into the first order or invoiced once, and who owns the tooling afterwards. Ownership should be written down, with the tooling listed and marked as brand property.
Plate and die life
Ask how many impressions a plate is expected to deliver and how wear is detected. A worn embossing plate produces progressively shallower logos, which passes inspection early in a run and fails later.
Cost of change after approval
A pattern revision after tooling is made carries a real cost. Ask what a revision costs and how long it takes, because a supplier who answers precisely is a supplier that has been through the process.
Line 6: Packing and Cartons
Poly bag and protection per unit
Poly bag thickness, tissue, stuffing paper and desiccant. These items look trivial per unit and total a measurable amount across a container, and their absence is visible only when the goods arrive creased.
Carton specification
Ply, board grade, dimensions and compression rating. A quote that specifies a five-ply carton and one that leaves it to the factory are not the same offer, and the difference is discovered at the destination port.
Carton configuration
Units per carton, carton weight, and whether mixed sizes are permitted. Mixed cartons reduce freight efficiency and slow receiving, so ask whether the price assumes single-SKU cartons.
Marking and labelling
Carton marks, barcode labels, size stickers and any retail-ready requirements. Retail-ready packing can add both material and labour, and it is frequently assumed rather than quoted.
Line 7: Inspection and Testing
Who inspects and to what standard
Factory self-inspection, third-party inspection or both, at which AQL and at whose cost. The inspection line is where cheap quotes usually differ most from complete ones.
Testing included in the price
Whether a quote includes restricted-substance testing, colour fastness, adhesion or hardware pull tests. Testing per material rather than per order is the norm, so confirm how many materials the quoted figure covers.
Re-inspection cost after failure
Ask who pays for a second inspection when the first fails. This single clause changes behaviour more than any promise about quality, because it moves the cost of failure to where the failure occurred.
Records provided with shipment
Inspection report, measurement sheet and test certificates included in the documentation pack. Where these are chargeable extras, the delivered cost is higher than the quoted one.
Line 8: Freight, Terms and Duties
Which incoterm the quote assumes
Ex works, FOB, CIF or DDP. Each moves a different set of costs and risks, and comparing an FOB quote with a DDP quote is the most common arithmetic error in wholesale sourcing.
Freight basis and volume
Whether freight is quoted at current rates or estimated, and whether it assumes full container or shared. A quote built on a rate from six months ago will not survive the booking.
Duty and tax treatment
For DDP quotes, confirm the duty rate used and the classification assumed. A DDP price built on the wrong tariff code is a price that will be revised after arrival.
Insurance and its exclusions
Marine insurance coverage and exclusions, particularly for water damage and handling. Where insurance is excluded, the exposure sits with the buyer for the entire transit.
Whose freight rate applies
Factories often quote a freight figure from their own forwarder, which may be higher or lower than yours. Ask for the ex works or FOB price and add your own freight rate, then compare both on the same basis.
Line 9: Payment Terms and Cost
The structure as quoted
Deposit percentage, balance timing and whether a letter of credit is required. Thirty percent deposit against seventy percent before shipment is a different cash profile from thirty against seventy on arrival.
The financing cost of the structure
Apply your own cost of capital to each structure and compare. A lower unit price with full prepayment can be more expensive than a higher price with staged terms once financing is counted.
Currency and adjustment clauses
Currency of the quote and whether a material surcharge clause exists. Unstated adjustment rights allow a price to move between order and shipment without a formal revision.
What happens on delay
Whether the payment schedule is tied to dates or to milestones. Milestone-based terms give the buyer leverage during production; date-based terms give it away at signature.
Line 10: MOQ and Price Breaks
The minimum that applies per colour
Minimum order quantity per style is common; minimum per colour or per material is stricter and far more expensive in practice. Ask both suppliers whether the minimum applies to the order or to each colourway.
Price breaks and their shape
Request the full ladder rather than the single quoted tier: the price at your volume, one tier below and one above. The shape of the curve tells you how much of the price is setup and how much is material.
Mixed-order allowance
Whether the minimum can be met across several styles. A supplier who allows a mixed container at the same unit price is offering flexibility worth more than a small price difference.
Volume commitments
Whether a better price requires a forecast, and what happens if the forecast is not met. Committed volume at an unachievable level is a penalty waiting to be invoiced.
Line 11: Lead Time Risk
What the quoted lead time covers
From deposit, from material arrival, or from sample approval. The three starting points differ by weeks, and the smallest number is usually measured from the most favourable one.
Material lead time separately
Ask for material lead time as its own figure. Where a special lining or a branded buckle is involved, material can dominate the schedule, and production lead time quoted without it is misleading.
The cost of a late arrival
Model the cost of the goods arriving three weeks late: air freight to recover, missed season, tied-up working capital. A ten-day difference in lead time can outweigh a five percent price gap once that number exists.
Schedule buffer and honesty
Ask what percentage of their orders shipped on time in the last quarter. A supplier who names a figure, even an imperfect one, is measuring; one who cannot is quoting an intention.
Line 12: Exclusions and Assumptions
The exclusions paragraph
Most quotes carry an exclusions or notes section, and it is the most valuable part of the document. Read it before the price, because it defines what the price does not buy.
Assumptions about your specification
Where a supplier assumed a material, a lining or a hardware grade, the assumption is a placeholder for a price change. Compare assumptions against your specification and price the delta.
Validity period
Quotes expire. A quote valid for fifteen days compared against one valid for ninety days is not a fair comparison unless you intend to order immediately, and the shorter validity usually signals an unstable material market.
Terms buried in the offer
Tolerance on quantity, rights to substitute materials of equal quality, and clauses about force majeure. Each is standard in some markets and each changes what arrives.
Building the Landed Cost
Every line above resolves into the same figure: the cost of one sellable bag in your warehouse. Build it once in a spreadsheet, then reuse it for every future quote rather than starting again.

The seven components to sum
Unit price, tooling amortised across the first order, packing materials not included, inspection and testing, freight to destination, duty and clearance, and the financing cost of the payment structure. Sum them per unit at your actual volume.
| Component | Supplier A | Supplier B |
|---|---|---|
| Quoted unit price | 12.40 FOB | 14.80 FOB |
| Tooling per unit | 0.35 | 0.20 |
| Packing extras | 0.18 | 0.00 |
| Inspection and testing | 0.42 | 0.00 |
| Freight per unit | 1.10 | 1.05 |
| Duty at 6.5 percent | 0.81 | 0.96 |
| Financing on terms | 0.26 | 0.09 |
| Landed cost | 15.52 | 17.10 |
Reading the result honestly
In the example the gap narrows from 2.40 to 1.58 and the ranking stays the same. That is a normal outcome. The value of the exercise is that the gap becomes a defensible number rather than an impression, and occasionally the ranking reverses.
Duty depends on the code
Duty is calculated on classification, so confirm both quotes assume the same tariff heading. Where one supplier quotes duty at a lower rate on a code that does not apply, the landed cost is understated by the full difference.
Keep the formula, not the file
A landed cost model is reusable across styles and suppliers. Build it once with your freight forwarder’s rates and your bank’s terms, and each new quote takes ten minutes rather than a morning.
Scoring the Non-Price Factors

Five factors worth weighting
Specification match, verified capability, communication quality, schedule reliability and commercial transparency. Score each from one to five with one sentence of evidence, and weight specification match highest for a first order.
Evidence beats impression
A score supported by a sample, a factory visit or an answered technical question is worth more than a score supported by a friendly sales contact. Record the evidence, because in six months the impression will have faded and the evidence will still settle the argument.
Weight before you score
Set weights before seeing the quotes. Weights set afterwards drift toward the supplier you already prefer, which converts a scoring exercise into a justification exercise.
What a close score means
Within three points out of twenty-five, the decision is close enough that terms should decide it: payment structure, lead time and the willingness to accept a trial order.
The Follow-Up Questions
One round, five questions
Send the same five questions to both suppliers and compare the quality of the answers rather than the speed. Which mill supplies the PU, what is the stitch density, what is included in the price, who pays for re-inspection, and what is the material lead time.
Written answers only
Written answers become part of the specification and can be quoted later. Verbal answers become a recollection that is denied at the moment it matters.
How to read a non-answer
A reply that restates the price without addressing the question is information about the supplier. Two non-answers in one round is a pattern, and the pattern is what you will experience during production.
The revised quote
Ask both suppliers to reissue the quote against your written specification. The revised pair is the first genuinely comparable set of documents you will hold.
Documenting the Decision
One page per supplier
Specification match, landed cost, score, open questions and the decision with a date. One page each, kept with the quotes, explains the choice to anyone who asks later, including your own finance team.
Record what you rejected
The reason a supplier was not chosen matters as much as the reason one was. Where a later order goes wrong, the alternative is already evaluated and the file shows why it was not selected.
The trial order clause
Whatever the comparison concludes, the first order should include a defined inspection standard, a milestone payment and a stated remedy for failure. These three items convert a price into an arrangement.
Review after the first shipment
Compare the delivered landed cost with the model and record the difference. The model improves with each order, and after three orders it becomes a reliable planning tool rather than an estimate.
Using the Comparison in Negotiation
Negotiate the line, not the total
Asking for a discount on the total invites a cut somewhere invisible. Asking about a specific line, such as why packing is charged separately or why the tooling sits at that figure, produces an answer that either reduces the cost or reveals what the price contains.
Never disclose the competing figure
A supplier told the rival price will meet it and recover the difference elsewhere. Describe the gap in specification instead, and let the supplier decide how to close it.
Trade specification for price deliberately
If a lower price is required, choose which specification gives way: lining weight, hardware plating, packing or inspection. A documented trade keeps the product coherent; a negotiated percentage does not.
The two-round rule
One round of questions, one revised quote, then a decision. Negotiations that run to five rounds usually end with a price nobody can trace and a specification that has quietly changed twice.
Comparing Repeat Order Quotes
Same basis as the first order
Repeat quotes should be compared on the specification that was actually produced, not the one originally quoted. Where a substitution was approved mid-programme, the repeat price must be measured against the substituted specification.
Material movement
Ask for the material component separately each time. Where the price rises, the split between material and labour tells you whether the increase is market-driven or margin-driven.
Tooling already paid
A repeat order should not carry a tooling charge for dies that already exist and are owned. Where it reappears, the question is whether the tooling was ever made or whether the line is a margin component.
Comparison Mistakes to Avoid
Comparing totals only
The single most expensive habit in wholesale sourcing. Two totals hide twelve lines, and the cheapest total usually contains the most assumptions.
Letting one supplier define the basis
Where the first quote received becomes the template, the comparison inherits its omissions. Build the spreadsheet from your specification before either quote arrives.
Treating lead time as free
Lead time has a cost when it is short and a larger one when it is wrong. Both belong in the comparison, weighted by how much a missed date would actually cost your business.
Comparing Samples Against the Quotes
One sample per quote, same specification
Order a sample from each supplier against the written specification and compare them against the quoted lines rather than against each other. Where a sample contradicts its own quote, the quote is the weaker document and should be revised before pricing is discussed again.
Weigh and measure, do not appraise
Weigh both samples, measure the same five dimensions and count stitches over a fixed length. Numbers survive the meeting; impressions do not, and the numbers frequently show two samples described identically are not.
What a sample cannot settle
Consistency, capacity and schedule reliability. A sample proves what one unit can be, not what the thousandth will be, which is why the comparison continues into the trial order rather than ending at approval.
Keep the rejected sample
Retain the sample from the supplier you did not choose, labelled and dated. It is a benchmark for the next comparison and a reminder of the specification you were offered at that price point.
When Both Quotes Are Above Budget
Separate specification cost from margin
Ask both suppliers to price a reduced specification against a defined target: lighter lining, standard plating, simpler edge, fewer cartons. If the price falls by roughly the material and labour removed, the margin is normal. If it barely moves, the gap is margin rather than cost.
Reduce scope before reducing quality
Fewer styles, fewer colourways, simpler packing or a longer delivery window usually recovers more than downgrading material. Quality reductions are permanent in the product; scope reductions are temporary in the programme.
Reconsider the volume assumption
Where both quotes are close to each other but above budget, the issue is usually volume rather than supplier. Test a price at a realistic annual volume before concluding that the market is expensive.
The honest option
Sometimes the specification is not achievable at the budget. Knowing that in week one allows the product to be reshaped; discovering it in week ten allows only a compromise.
A Reusable Comparison Template
One sheet, four columns: your specification, supplier A, supplier B, and the gap between them expressed per unit. The rows below are the minimum that makes a comparison meaningful.
| Row | What to enter |
|---|---|
| Material | Substrate, weight, coating, mill |
| Lining | Material, weight, colour |
| Construction | Stitch density, seam allowance, reinforcement |
| Hardware | Alloy, plating, weight per piece, zip spec |
| Operations | Tick list of every process included |
| Tooling | One-time charges and amortisation basis |
| Packing | Unit protection, carton spec, marking |
| Inspection | AQL, provider, testing scope, re-inspection cost |
| Commercial | Incoterm, payment, MOQ, lead time, validity |
| Exclusions | Copied verbatim from the quote |
Why four columns and not two
Two columns answer which is cheaper. Four columns answer which is cheaper for the product you specified, and the gap column shows where the difference actually sits rather than how large it is.
Keep the template under version control
Name it with a date and keep every revision. When a supplier’s price changes, the reason should be visible in the rows rather than inferred from the total.
Hand it to the supplier
Send the specification columns to both suppliers and ask them to complete their side. A quote returned in your own structure is already half compared, and the exercise removes most of the ambiguity that causes later disputes.
Where to keep it
One folder per programme, containing the specification, every quote version, the landed cost sheet and the decision note. When a price is questioned a year later, the folder answers in minutes.
FAQ
What is the fastest way to compare two bag quotes?
Put both on the same currency, incoterm and quantity, then add a third column with your own specification. From there, compare twelve lines: material, construction, hardware, operations, tooling, packing, inspection, freight, payment, MOQ, lead time and exclusions.
Should the cheapest quote usually win?
Only after the landed cost is calculated and the exclusions are read. In practice the cheapest headline price is frequently the most incomplete quote, and the landed cost gap narrows or reverses once tooling, packing, inspection and payment terms are counted.
How much does packing really matter?
Individually small, collectively measurable. Poly bags, tissue, stuffing, desiccant, carton grade and carton configuration commonly total three to six percent of unit cost, and an under-specified carton produces damage claims that exceed the saving.
What if one supplier will not break down the price?
Ask for a split between material, labour and overhead rather than a full open-book costing. A supplier who refuses even that is asking you to compare a number with no content, and that refusal belongs in the scoring.
How do I price the risk of a late shipment?
Estimate the recovery cost: air freight per kilogram for the shortfall, the margin lost on a missed season, and the working capital tied up in stock that cannot sell. Divide by the order quantity to express it per unit, then add it to the landed cost.
Is a higher MOQ always a worse deal?
Not necessarily. A higher MOQ with a stable price and a dedicated line can be better than a low MOQ priced at a premium with shared capacity. The comparison should be cost per unit at your realistic annual volume, not per order.
How many suppliers should I compare?
Two properly compared is more useful than five skimmed. Three is workable when one is an incumbent being benchmarked. Beyond that the marginal information is small and the specification work grows.
What belongs in the specification column?
Material substrate and weight, coating, lining, hardware grade and plating, stitch density, seam allowance, reinforcement, edge treatment, packing, inspection standard, testing scope, incoterm, payment structure, MOQ and lead time. Fifteen rows is enough to expose most differences.
How do I compare quotes in different currencies?
Convert at a single rate on a single date and record both the rate and the date. Then ask each supplier whether the price is fixed in their currency or adjustable, because the answer determines which quote carries currency risk.
When is a trial order better than more comparison?
When the two quotes are within a few percent on landed cost and the specification match is similar. At that point the remaining uncertainty is behavioural, and a small trial order reveals more about reliability than another round of documents.
What should I do if a quote has no exclusions section?
Ask for one in writing. A quote without exclusions either includes everything, which is rare, or has not been thought through. The written answer becomes part of the specification you will hold the supplier to.
How do tooling charges affect repeat orders?
Tooling paid once should not recur. Confirm ownership in writing, keep the tooling on a list marked as brand property, and check that repeat quotes exclude it. Recurring tooling charges are a margin line, not a cost.
Does a lower price ever justify a weaker inspection standard?
Only if you accept the resulting defect rate and its cost. Model a two percent reject rate on the order and add the rework, replacement and freight; in most wholesale programmes that number exceeds the price difference.
What is the one line buyers most often miss?
Exclusions and assumptions. They are usually at the bottom of the second page, they are rarely read, and they define everything the price does not include. Read them before the total, not after.
Send both quotes and we will price them the same way.
Share your specification, target volume and destination market with info@gionar.com. We reply with a line-by-line quotation that separates material, labour, tooling, packing and inspection, so the comparison is between products rather than between numbers.

